6.2 DFPT phonons
These are unexecuted teaching inputs and starting settings to test. Original figures are schematics, not computed results. Use licensed VASP and PAW data, replace every placeholder, record the executable version and validate convergence.
6.2.1 Model, units and provenance
Use eV for energy, Å for length and eV/Å for force; 1 kbar = 0.1 GPa. State normalization per atom, molecule, primitive cell or simulation cell. Record PAW identifiers, release, ZVAL, ENMAX and permitted hashes; never redistribute POTCAR. SCF convergence addresses the chosen electronic problem; convergence of the target property requires separate tests.
Original schematic. Curves explain concepts; blank data areas await verified learner results. No calculation is claimed.
6.2.2 Worked case: procedure, interpretation and checks
What changes relative to finite displacements?
Finite differences push atoms a small but finite distance. Density-functional perturbation theory solves the electronic response to an infinitesimal displacement. Both target the same harmonic curvature when their approximations and numerical settings match. DFPT avoids choosing a finite displacement amplitude, but it does not remove basis, k-point, response-convergence, or finite-supercell errors.
For the traditional VASP IBRION=8 workflow, the calculated dynamical information is at Γ of the supplied cell. Γ of a primitive cell is not a full phonon dispersion. Γ of a supercell contains folded information that external interpolation tools can convert to real-space force constants and primitive-cell dispersions. Do not assume that every newer VASP electron–phonon/phonon workflow shares identical capabilities; check the installed version and method documentation.
Stepwise lesson
First repeat a primitive-cell Γ calculation for a nonpolar insulating crystal whose relaxed structure is already available. Use the same physical model as 6.1 Finite-displacement phonons with Phonopy. Then build a matched supercell and repeat if a full dispersion is needed.
- Verify residual forces are small and the cell matches the intended equilibrium state. A Hessian at an unconverged point is a curvature at that point, not automatically an equilibrium spectrum.
- Run the response calculation with tight electronic accuracy and a supported functional/method combination. The documented traditional displacement-DFPT implementation is limited to LDA/GGA; do not apply this template to hybrid or meta-GGA calculations. Check the installed release for further compatibility constraints rather than assuming metallic, spin-orbit, and other options can be combined arbitrarily.
- Inspect the frequency/eigenvector section of OUTCAR and the electronic/linear-response convergence record. Count 3N modes for N atoms in the supplied cell; identify near-zero translations.
- If using a supercell with Phonopy, preserve its generation metadata and extract force constants through the documented VASP-DFPT interface. Do not reuse a displacement FORCE_SETS file from a different cell.
- Compare a few frequencies/eigenvectors with a converged finite-displacement calculation on precisely the same cell. Agreement is a valuable method check, not a reason to skip independent supercell convergence.
**External extraction example
This is a response input, not an instruction to perform a structural optimization. NSW=1 supplies a response-step setting; it is not evidence that the initial geometry is relaxed. LEPSILON=.TRUE. can be a separate, supported route to electronic dielectric response and Born charges in suitable insulating systems; it should be added only with a clear purpose and compatibility check. Full elastic constants require strain response and cannot be obtained merely by reading atomic displacement DFPT as if it were strain DFPT.
Output interpretation, exercise, and figure
A mode eigenvector describes a collective displacement pattern, not the trajectory of one isolated atom. Close or degenerate modes can rotate within their subspace; compare subspaces or displacement character rather than demanding identical vector signs. THz, cm⁻¹, and meV are alternate frequency/energy reporting units. Imaginary modes retain the same stability interpretation as in finite differences. An optical Γ frequency alone says nothing about an instability at the zone boundary.
Exercise: compare Γ modes from primitive-cell DFPT to those from the matched supercell calculation. Separate primitive Γ modes from folded nonzero-wavevector modes. Explain why the supercell reports more modes without creating additional physical branches in the primitive representation.
6.2.3 Unexecuted inputs and analysis scaffolds
These are unexecuted teaching inputs and starting settings to test. Original figures are schematics, not computed results. Use licensed VASP and PAW data, replace every placeholder, record the executable version and validate convergence.
6.2.3.1 Input block 1
# Traditional VASP displacement DFPT response calculation
IBRION = 8
NSW = 1
ISIF = 2
PREC = Accurate
EDIFF = 1E-8
LREAL = .FALSE.
# No finite displacement POTIM is needed to define DFPT amplitude.
6.2.4 Related learning paths
- 1.1 Four input files, one physical question
- 1.2 A convergence laboratory with an error budget
- 6.1 Finite-displacement phonons with Phonopy
- 6.3 Harmonic free energy, heat capacity, and entropy